Resources · Water

How Deep Is the Water Table in MD of Greenview?

Buyers ask this before they bid, and drillers ask it before they quote. In MD of Greenview, nearby well records point to an average completed well depth of about 50 m, with static water levels often in the 8–25 m range. The predominant aquifer on file for this part of Alberta is the Wapiti Formation sandstone and surficial sand aquifers.

Those numbers are county-scale context. They are not a promise for the quarter you are walking. The depth and static-level figures are regional estimates from typical Alberta well records in this belt, not a surveyed water table on your parcel.

Greenview spans farmland around Valleyview to the mountains at Grande Cache, so one well number is a rough guide at best. Wapiti sandstone wells are deep and often sodium-rich; sand lenses near Sturgeon Lake give shallower water.

What a “water table” number actually is in MD of Greenview

Around Valleyview and the rest of MD of Greenview, people use “water table” for three different things:

• Static water level — the resting height of water in a completed well, measured from ground surface.
• Completion depth — how far the driller had to go to find a usable interval.
• Seasonal high water — how close water sits to the surface in a wet year, which matters for basements, septic, and dugouts.

A listing that says “good water at 80 feet” is usually mixing those ideas. Eighty feet of steel is a completion depth. The pump may still hang much shallower if the static level is high. Or the well may be deep and the static level may still sit far down the hole in late summer.

In MD of Greenview, treat 50 m as a planning band for completion, and 8–25 m as a planning band for static level. If a seller’s story sits far outside both bands, ask for the well ID and the last pump test.

What this means before you drill in MD of Greenview

Budget three line items on a MD of Greenview acreage, not one:

• Drilling and casing to a depth that can overshoot the neighbour’s well. In this county, planning around 50 m plus a contingency is more honest than copying the shallowest well on the road.
• A pump test, not a “we hit water” photo. Yield, drawdown, and recovery decide whether the well is a household supply.
• Water chemistry. Iron, hardness, sulphur, and bacteria are independent of depth. A cheap shallow well can still need treatment.

The Wapiti Formation sandstone and surficial sand aquifers is common in this part of the province, but contacts shift. A buried-valley sand and a bedrock sandstone can sit under adjacent quarters. That is why a free parcel report that plots nearby well records is worth more than a single county average.

Flood and surface water are a separate file. In MD of Greenview, notable mapped or commonly discussed hazard areas include Little Smoky River, Smoky River valley, Sturgeon Lake shoreline. A wet corner of a field is not automatically a well. It may be a wetland, a flood fringe, or both.

Reading a well record in MD of Greenview

Alberta well reports usually list location, date, lithology, completion interval, static level, and a test rate. When you pull neighbours near Valleyview:

• Prefer wells within a kilometre, then compare geology, not just depth.
• Ignore abandoned holes unless you want to know where not to drill.
• Note the year. A 1978 farm well and a 2019 domestic well are not the same construction standard.
• If three nearby wells finish near 50 m and one is 15 m, ask why. The shallow one may be a sand point, a dugout well, or a different aquifer.

Permits, setbacks, and the rest of the MD of Greenview water file

A new well in MD of Greenview is only one approval. Earthworks for a pond, a dugout, or a crossing can trigger the Water Act. Mapped wetlands near Valleyview and across MD of Greenview are common enough that you should not assume a “just a slough” story. Keep well planning and wetland planning in two piles so a good aquifer does not talk you into filling a regulated wetland.

See this for your specific parcel

County averages help you decide whether a listing is in the right universe. They cannot replace a pin on the map.

Generate a free land report for a property in MD of Greenview →

The report is built to show water context, nearby records where available, and the other pillars — terrain, wetlands, climate, vegetation — on the same parcel.

Sampled data for MD of Greenview

From a Land Intelligence report run on a representative quarter in Township 68, Range 26, W5. These are measured or record-based values for that location, shown to put the county figures above in context. They are not your parcel.

Neighbouring counties: County of Grande Prairie (78 km) · Birch Hills County (94 km) · MD of Smoky River (97 km) · Big Lakes County (100 km) · Compare MD of Greenview with another county

Sampled from the live report pipeline at a representative quarter in Township 68, Range 26, W5 on 2026-10-08: solar irradiance (12 well records within 5 km). Kept as regional estimates: well depth (only 12 nearby records at the sample point); hardiness zone (point sample read 3b, more than a half-zone from the regional label). Text reviewed 2026-10-09. Methodology.

Common questions

Is MD of Greenview a good place to drill a well?

Many rural parcels in MD of Greenview use private wells. Whether yours is “good” depends on the aquifer interval, chemistry, and a pump test — not the county average.

Can I use the neighbour’s well depth in MD of Greenview?

Only as a hint. Geology can change between quarters. Pull the well ID and lithology before you copy a depth into a budget.